Difficulty
Moderate
Steps
16
Time Required
15 - 25 minutes
Sections
3
- Battery
- 12 steps
- Charging Port
- 3 steps
- Speaker
- 1 step
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackHP Slate 7 4601
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
- Back CoverBatteryCharging PortSpeaker Unit
Prepare your required tools, a new speaker unit for your tablet, and set aside about 15 to 25 minutes to delve into the inner workings of your HP Slate.
What you need
Step 1
Battery
- Begin your replacement by using a T3 or T4 Torx screwdriver.
- Remove the two 1.4mm x 3mm Torx Head screws at the top of the device.
Begin your replacement by using a T3 or T4 Torx screwdriver.
Remove the two 1.4mm x 3mm Torx Head screws at the top of the device.
1024
Step 2
- With the pointed end of the spudger, remove the thin metal band.
- It is easiest to remove the metal band through the headphone opening.
With the pointed end of the spudger, remove the thin metal band.
It is easiest to remove the metal band through the headphone opening.
Step 3
- Using the flat end of the spudger, pry back the rear plastic cover.
- As you work your way around the edge, several “pop” noises will be made. These noises are caused by the plastic clips coming undone.
Using the flat end of the spudger, pry back the rear plastic cover.
As you work your way around the edge, several “pop” noises will be made. These noises are caused by the plastic clips coming undone.
Step 4
- Remove the rear cover.
Remove the rear cover.
Step 5
- Locate and remove the yellow tape covering the red and white speaker wires.
Locate and remove the yellow tape covering the red and white speaker wires.
Step 6
- Using the pointed end of the spudger, push both sides of the speaker wire connector out of its base.
- Push the same amount on both sides of the connector to avoid jamming or twisting its metal pins.
- Do not yank or pull on the speaker wires, since they are fragile. Only push on the white connector.
Using the pointed end of the spudger, push both sides of the speaker wire connector out of its base.
Push the same amount on both sides of the connector to avoid jamming or twisting its metal pins.
Do not yank or pull on the speaker wires, since they are fragile. Only push on the white connector.
Step 7
- Gently pull back the foil covering the gold charging port ribbon.
Gently pull back the foil covering the gold charging port ribbon.
Step 8
- Using the flat end of the spudger, lift up the black panel covering the charging port connector.
- Gently slide the charging port ribbon out from its housing.
- It may be easier to use the pointed end of the spudger than your fingers.
Using the flat end of the spudger, lift up the black panel covering the charging port connector.
Gently slide the charging port ribbon out from its housing.
It may be easier to use the pointed end of the spudger than your fingers.
Step 9
- Lift gold charging strip away from the battery.
Lift gold charging strip away from the battery.
Step 10
- Push the white battery connector out of its housing using the pointed end of the spudger.
Push the white battery connector out of its housing using the pointed end of the spudger.
Step 11
- Using the #00 Phillips Head screwdriver, remove the 5 screws holding the battery in place.
- The four 1.75mm x 3mm silver Phillips Head screws circled in red are interchangeable.
- The black 1.75mm x 4mm Phillips Head screw must go back to the same spot during reassembly.
Using the #00 Phillips Head screwdriver, remove the 5 screws holding the battery in place.
The four 1.75mm x 3mm silver Phillips Head screws circled in red are interchangeable.
The black 1.75mm x 4mm Phillips Head screw must go back to the same spot during reassembly.
Step 12
- Lift battery out of its place and set aside.
Lift battery out of its place and set aside.
Step 13
Charging Port
- To free the speaker assembly, you will need a #00 Phillips Head screwdriver.
- Remove the two 1.75mm x 3mm Phillips Head screws from the speaker assembly.
To free the speaker assembly, you will need a #00 Phillips Head screwdriver.
Remove the two 1.75mm x 3mm Phillips Head screws from the speaker assembly.
Step 14
- Pull back the foil overlapping the charging port to reveal another 1.75mm x 3mm Phillips Head screw.
- Remove the screw with a #00 Phillips Head screwdriver.
Pull back the foil overlapping the charging port to reveal another 1.75mm x 3mm Phillips Head screw.
Remove the screw with a #00 Phillips Head screwdriver.
Step 15
- Lift the charging port and set it aside.
Lift the charging port and set it aside.
Step 16
Speaker
- Lift the two speakers out of the device and set them aside.
Lift the two speakers out of the device and set them aside.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Zachary
Member since: 04/14/2014
1,441 Reputation
2 Guides authored
Badges:
19
+16 more badges
Team
Cal Poly, Team 13-30, Maness Spring 2014
Member of Cal Poly, Team 13-30, Maness Spring 2014
CPSU-MANESS-S14S13G30
3 Members
8 Guides authored
