Htc Droid Incredible Dual Led Flash Replacement Repair Guide

Difficulty

Moderate

Steps

14

Time Required

                          20 - 35 minutes            

Sections

4

• Battery
• 3 steps
• MicroSD card
• 2 steps
• Rear Inner Frame
• 7 steps
• Dual LED FLash
• 2 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackHTC Droid Incredible

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Press your thumbnail into the slot between the rear panel and the front case located in the bottom of the phone.
• Useful tip: a penny or dime works in a pinch if you can’t use your thumbnail.
• Gently pry the rear panel up and away from the phone. You may need to slide your thumb up the crack to separate the rear panel from the front case.

Press your thumbnail into the slot between the rear panel and the front case located in the bottom of the phone.

Useful tip: a penny or dime works in a pinch if you can’t use your thumbnail.

Gently pry the rear panel up and away from the phone. You may need to slide your thumb up the crack to separate the rear panel from the front case.

1024

Step 2

• Remove the rear panel from the phone.

Remove the rear panel from the phone.

Step 3

• Insert a fingertip into the gap between the battery and the rear inner frame, located between the battery and the speaker. Slide the battery away from the speaker, widening the gap.
• Lift the top of the battery up and remove the battery from the rear inner frame.

Insert a fingertip into the gap between the battery and the rear inner frame, located between the battery and the speaker. Slide the battery away from the speaker, widening the gap.

Lift the top of the battery up and remove the battery from the rear inner frame.

Step 4

              MicroSD card               

• Press the MicroSD card further into its slot until it clicks.
• Release the MicroSD card, and it will pop out slightly.

Press the MicroSD card further into its slot until it clicks.

Release the MicroSD card, and it will pop out slightly.

Step 5

• Pull the MicroSD card straight out of its slot.

Pull the MicroSD card straight out of its slot.

Step 6

              Rear Inner Frame               

• Remove four T6 Torx screws securing the rear inner frame to the front case.

Remove four T6 Torx screws securing the rear inner frame to the front case.

Step 7

• The rear inner frame is attached to the front case by nine plastic clips, marked here for reference.

The rear inner frame is attached to the front case by nine plastic clips, marked here for reference.

Step 8

• Starting on the bottom of the phone, gently push in on the (red) rear inner frame behind each black clip with a small flathead screwdriver.
• Go slow and be gentle, you may have to go back and forth between each side several times to work the rear inner case free.

Starting on the bottom of the phone, gently push in on the (red) rear inner frame behind each black clip with a small flathead screwdriver.

Go slow and be gentle, you may have to go back and forth between each side several times to work the rear inner case free.

Step 9

• Loosen the clips on the side next to the camera using the method described in the previous step.

Loosen the clips on the side next to the camera using the method described in the previous step.

Step 10

• Rotate the phone 180 degrees and loosen the three clips on the side by the speaker. Note that the middle clip on this side is smaller than the others.

Rotate the phone 180 degrees and loosen the three clips on the side by the speaker. Note that the middle clip on this side is smaller than the others.

Step 11

• Use the same technique to loosen the clip on the top of the phone.
• You may need to gently lift the bottom of the rear inner frame to free this clip.

Use the same technique to loosen the clip on the top of the phone.

You may need to gently lift the bottom of the rear inner frame to free this clip.

Step 12

• Remove the rear inner frame.

Remove the rear inner frame.

Step 13

              Dual LED FLash               

• Remove two #000 Phillips screws attaching the Dual LED Flash board to the Rear Inner Frame.

Remove two #000 Phillips screws attaching the Dual LED Flash board to the Rear Inner Frame.

Step 14

• Use a small flathead screwdriver to gently pry the dual LED flash board off the posts holding it to the rear inner frame.
• Remove the dual LED flash board from the rear inner frame.

Use a small flathead screwdriver to gently pry the dual LED flash board off the posts holding it to the rear inner frame.

Remove the dual LED flash board from the rear inner frame.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 

                    Andrew Optimus Goldheart                     

Member since: 10/17/2009

491,689 Reputation

                                      411 Guides authored                  



                       Badges:
                       44







                                                        +41 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored