Htc One Remix Speaker Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 - 35 minutes

Sections

Speaker
15 steps

Flags

BackHTC One Remix
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Speaker

Use the sim eject tool to remove the SIM cards on either side of the phone.

Use the sim eject tool to remove the SIM cards on either side of the phone.

1024

Step 2

Place the warm iOpener on the top of the phone for three minutes.
iOpener Instructions

Place the warm iOpener on the top of the phone for three minutes.

iOpener Instructions

Step 3

Once the top of the phone is warm, use a plastic spudger to pry the top left corner up.
The top is glued on so it may be difficult to get off.

Once the top of the phone is warm, use a plastic spudger to pry the top left corner up.

The top is glued on so it may be difficult to get off.

Step 4

Remove the single 3 mm screw that is on the top left side using a Torx 4 screwdriver.

Remove the single 3 mm screw that is on the top left side using a Torx 4 screwdriver.

Step 5

Use the plastic prying tool to pry off the back cover. Place the tool in the SIM card insert and lift off the back cover with force. Continue to do this all around the phone.
Be careful to not break the wiring that is connected from the inside to the back of the phone.

Use the plastic prying tool to pry off the back cover. Place the tool in the SIM card insert and lift off the back cover with force. Continue to do this all around the phone.

Be careful to not break the wiring that is connected from the inside to the back of the phone.

Step 6

With tweezers, remove the small pieces of yellow tape that cover the zif connectors.
Use the plastic prying tool to take off the three pieces of silver tape. They are located at the bottom right corner of the copper plate.

With tweezers, remove the small pieces of yellow tape that cover the zif connectors.

Use the plastic prying tool to take off the three pieces of silver tape. They are located at the bottom right corner of the copper plate.

Step 7

With the plastic spudger, disconnect the eight ZIF connectors. Do this by lifting the small white lines up and pulling the ribbon from it.
Use tweezers to carefully detach the eight ribbon cables from the connectors.

With the plastic spudger, disconnect the eight ZIF connectors. Do this by lifting the small white lines up and pulling the ribbon from it.

Use tweezers to carefully detach the eight ribbon cables from the connectors.

Step 8

Remove the two 1 mm screws at the bottom right of the motherboard using a Torx 4 screwdriver.

Remove the two 1 mm screws at the bottom right of the motherboard using a Torx 4 screwdriver.

Step 9

Pull off one end of each of the five colored connecting cables from the motherboard.
Pull the black and red wire from the motherboard on the bottom left.
Below the bottom left gold cable.

Pull off one end of each of the five colored connecting cables from the motherboard.

Pull the black and red wire from the motherboard on the bottom left.

Below the bottom left gold cable.

Step 10

Remove the four 3 mm screws on each corner of the motherboard using a Torx 4 screwdriver.
Gently lift the motherboard out of the phone using the plastic opening tool.
Make sure the ribbon cables are out of the way when removing the motherboard.

Remove the four 3 mm screws on each corner of the motherboard using a Torx 4 screwdriver.

Gently lift the motherboard out of the phone using the plastic opening tool.

Make sure the ribbon cables are out of the way when removing the motherboard.

Step 11

With a plastic opening tool, remove the black speaker at the bottom of the phone.

With a plastic opening tool, remove the black speaker at the bottom of the phone.

Step 12

Loosen the camera on the phone using a plastic opening tool.
Do not detach the camera from the phone itself.

Loosen the camera on the phone using a plastic opening tool.

Do not detach the camera from the phone itself.

Step 13

Remove the gold tape at the top right corner of the phone and disconnect the ribbon wire from the circuit board.

Remove the gold tape at the top right corner of the phone and disconnect the ribbon wire from the circuit board.

Step 14

Remove the four 1mm screws on the circuit board using a Phillips #00 screwdriver.
Remove the circuit board.

Remove the four 1mm screws on the circuit board using a Phillips #00 screwdriver.

Remove the circuit board.

Step 15

Using a plated screwdriver, remove the magnetic speaker from the phone itself.

Using a plated screwdriver, remove the magnetic speaker from the phone itself.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors

                    Marcos Loza

Member since: 04/10/2018

936 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Eastern Washington University, Team S2-G4, Ramos Spring 2018                        

                                                  Member of Eastern Washington University, Team S2-G4, Ramos Spring 2018 



                    EWU-RAMOS-S18S2G4                     


                                            5 Members                     


                                            4 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team