Htc Wizard 200 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Battery
1 step
Back Panel
5 steps
Motherboard
5 steps
Keyboard Slider
1 step
Screen Cover
8 steps
LCD Screen
1 step

Flags

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

BackHTC Wizard 200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

To expose the battery, remove the outer case with your fingernail.
Remove the battery by pulling the black tab.

To expose the battery, remove the outer case with your fingernail.

Remove the battery by pulling the black tab.

1024

Step 2

              Back Panel

Insert the flat end of the spudger into the two notches on the back of the camera cover and pry them up.

Insert the flat end of the spudger into the two notches on the back of the camera cover and pry them up.

Step 3

Work the spudger around the edges of the camera cover until it comes off.

Work the spudger around the edges of the camera cover until it comes off.

Step 4

Remove the four 6 mm screws with the T5 Torx screwdriver.
One of the screws is under the “void” sticker.

Remove the four 6 mm screws with the T5 Torx screwdriver.

One of the screws is under the “void” sticker.

Step 5

Insert the flat end of an iFixit opening tool between the side and inner covers to create a gap.
Work the tool around the edges until all the clips release.

Insert the flat end of an iFixit opening tool between the side and inner covers to create a gap.

Work the tool around the edges until all the clips release.

Step 6

Once all the clips are open, remove the inner panel from the phone.

Once all the clips are open, remove the inner panel from the phone.

Step 7

              Motherboard

Use the spudger to pry the camera off.

Use the spudger to pry the camera off.

Step 8

Using tweezers, flip the connector latch away from the motherboard.
Detach the flexible connection from under the connector latch.

Using tweezers, flip the connector latch away from the motherboard.

Detach the flexible connection from under the connector latch.

Step 9

Slide the keyboard into the open position.

Slide the keyboard into the open position.

Step 10

Lift the motherboard out of the case using the spudger.
Expose the underside of the motherboard using your hands.

Lift the motherboard out of the case using the spudger.

Expose the underside of the motherboard using your hands.

Step 11

Remove the flexible connection from the motherboard.
Caution: Removing the connection too fast may cause damage to the connection and cables.

Remove the flexible connection from the motherboard.

Caution: Removing the connection too fast may cause damage to the connection and cables.

Step 12

              Keyboard Slider

Remove the four 5mm screws with the T5 Torx screwdriver.
Remove the keyboard slider from the main body.

Remove the four 5mm screws with the T5 Torx screwdriver.

Remove the keyboard slider from the main body.

Step 13

              Screen Cover

Use the T5 Torx screwdriver to remove four 5mm screws that secure the back of the screen casing.

Use the T5 Torx screwdriver to remove four 5mm screws that secure the back of the screen casing.

Step 14

Insert the plastic opening tool between the front panel and the rear panel and pry open to reach the screen.

Insert the plastic opening tool between the front panel and the rear panel and pry open to reach the screen.

Step 15

Once the rear panel is loose, lift it off of the front panel.
The flexible connection will pop loose.

Once the rear panel is loose, lift it off of the front panel.

The flexible connection will pop loose.

Step 16

Device rotated 90 degrees CCW.
Remove the yellow anti-static tape.

Device rotated 90 degrees CCW.

Remove the yellow anti-static tape.

Step 17

Unscrew the two 3mm phillips #0 screws from the bottom of the device that secure the rigid flex board to the screen panel.

Unscrew the two 3mm phillips #0 screws from the bottom of the device that secure the rigid flex board to the screen panel.

Step 18

Device rotated 180 degrees CW.
Unscrew the two 3mm phillips #0 screws from the top of the device that secure the rigid flex board to the screen panel.

Device rotated 180 degrees CW.

Unscrew the two 3mm phillips #0 screws from the top of the device that secure the rigid flex board to the screen panel.

Step 19

Device rotated 90 degrees CCW.
Unhinge the flexible connection and use the tweezers to disconnect.

Unhinge the flexible connection and use the tweezers to disconnect.

Step 20

Now that the rigid flex board is loose, remove it from the screen.

Now that the rigid flex board is loose, remove it from the screen.

Step 21

              LCD Screen

Simply pull out the loose screen.

Simply pull out the loose screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    Kyle Champ

Member since: 10/03/2011

225 Reputation

                                      12 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 20-27, Maness Fall 2011                        

                                                  Member of Cal Poly, Team 20-27, Maness Fall 2011 



                    CPSU-MANESS-F11S20G27                     


                                            4 Members                     


                                            24 Guides authored

Markup Mishap#

Introduction#

What you need#

Team#

Markup Mishap

Introduction

What you need

Team