Difficulty
Moderate
Steps
15
Time Required
10 minutes
Sections
4
- Display Assembly
- 5 steps
- Front Camera
- 4 steps
- Rear Camera
- 1 step
- Motherboard
- 5 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackHuawei MediaPad M3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Display Assembly
- Use a heat gun to heat the display. It may take up to 30 seconds.
- Slide in the opening picks to the four corners of the tablet and peel off the display carefully.
Use a heat gun to heat the display. It may take up to 30 seconds.
Slide in the opening picks to the four corners of the tablet and peel off the display carefully.
1024
Step 2
- Open the display carefully.
- Use a Phillips #00 screwdriver to remove the two 3.0mm screws.
Open the display carefully.
Use a Phillips #00 screwdriver to remove the two 3.0mm screws.
Step 3
- After removing the two screws, use your hand to take out the silver metal bracket.
After removing the two screws, use your hand to take out the silver metal bracket.
Step 4
- Use the plastic opening tool to disconnect the two ribbon cable connectors.
Use the plastic opening tool to disconnect the two ribbon cable connectors.
Step 5
- Remove the display assembly from the device.
Remove the display assembly from the device.
Step 6
Front Camera
- Use a Phillips #00 screwdriver to remove the six 3.0mm screws.
Use a Phillips #00 screwdriver to remove the six 3.0mm screws.
Step 7
- Use your hand to remove the silver metal bracket.
Use your hand to remove the silver metal bracket.
Step 8
- Use your hand to remove the two black plastic covers.
Use your hand to remove the two black plastic covers.
Step 9
- Use a plastic opening tool to remove the front camera.
Use a plastic opening tool to remove the front camera.
Step 10
Rear Camera
- Disconnect and remove the camera from the motherboard.
Disconnect and remove the camera from the motherboard.
Step 11
Motherboard
- Use a Phillips #00 screwdriver to remove this 3mm screw.
- Remove the small silver metal bracket.
Use a Phillips #00 screwdriver to remove this 3mm screw.
Remove the small silver metal bracket.
Step 12
- First, remove the right ribbon cable from the board.
- Next, remove the left ribbon cable from the board.
First, remove the right ribbon cable from the board.
Next, remove the left ribbon cable from the board.
Step 13
- Use a Phillips #00 screwdriver to remove the 3mm screw present on top of the silver metal bracket.
- Remove the silver metal bracket from the board.
- Remove the yellow ribbon cable using a plastic opening tool.
Use a Phillips #00 screwdriver to remove the 3mm screw present on top of the silver metal bracket.
Remove the silver metal bracket from the board.
Remove the yellow ribbon cable using a plastic opening tool.
Step 14
- Use a Phillips #00 screwdriver to remove the two 3mm screws.
- Remove the black plastic cover from the board.
- Remove the yellow ribbon cable using a plastic opening tool.
Use a Phillips #00 screwdriver to remove the two 3mm screws.
Remove the black plastic cover from the board.
Step 15
- Carefully remove the motherboard from the device by using a plastic opening tool.
Carefully remove the motherboard from the device by using a plastic opening tool.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 6 other contributors
Kefan Lin
Member since: 10/01/2019
515 Reputation
4 Guides authored
Badges:
8
+5 more badges
Team
Duke University Pratt School of Engineering, Team S5-G2, Matos-Garner Fall 2019
Member of Duke University Pratt School of Engineering, Team S5-G2, Matos-Garner Fall 2019
DUKEPSE-MATOS-GARNER-F19S5G2
5 Members
4 Guides authored
