Difficulty
Easy
Steps
8
Time Required
5 - 10 minutes
Sections
1
- LCD Screen
- 8 steps
Flags
3
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Better Introduction
Improve this guide by completing or revising its introduction.
BackHuawei Ascend Y300
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the rear cover at the back by pulling the gap located at the bottom of the phone.
- Lift up and remove the battery.
Remove the rear cover at the back by pulling the gap located at the bottom of the phone.
Lift up and remove the battery.
1024
Step 2
- Leave the phone down on a table.
- 8 screws are what we need to remove next. There is one hiding below a white sticker.
Leave the phone down on a table.
8 screws are what we need to remove next. There is one hiding below a white sticker.
Step 3
- Use a screwdriver (T4 if you are using the 54 bit driver kit) to remove the 8 screws along the edges of the phone. There are four in each corner and four in the middle on the sides.
- Put the screws on the magnetic mat/parts tray or bowl to make sure they are not lost.
Use a screwdriver (T4 if you are using the 54 bit driver kit) to remove the 8 screws along the edges of the phone. There are four in each corner and four in the middle on the sides.
Put the screws on the magnetic mat/parts tray or bowl to make sure they are not lost.
Step 4
- Use the plastic opening tool by fitting it into the gaps to pull back the frame.
Use the plastic opening tool by fitting it into the gaps to pull back the frame.
Step 5
- On the left of the motherboard there is a ribbon cable that connects the volume rocker to the motherboard, we need to disconnect it.
- To do this, using either the spudger or tweezers lift up the retention flap holding the cable down.
- Next using the tweezers carefully pull the ribbon cable away from the socket it was in until it is completely clear of the connector.
On the left of the motherboard there is a ribbon cable that connects the volume rocker to the motherboard, we need to disconnect it.
To do this, using either the spudger or tweezers lift up the retention flap holding the cable down.
Next using the tweezers carefully pull the ribbon cable away from the socket it was in until it is completely clear of the connector.
Step 6
- There are two more ribbon cables at the top that must also be disconnected, to do this simply lift them up from their connecter with the tweezers or with the spudger.
There are two more ribbon cables at the top that must also be disconnected, to do this simply lift them up from their connecter with the tweezers or with the spudger.
Step 7
- Pull back the orange tab. Carefully disconnect this.
Pull back the orange tab. Carefully disconnect this.
Step 8
- Once the orange tabs are pulled back, use a plastic wedge to detach the LCD screen.
- Carefully pull the screen away from the cover and replace the LCD with a new one
Once the orange tabs are pulled back, use a plastic wedge to detach the LCD screen.
Carefully pull the screen away from the cover and replace the LCD with a new one
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
44 other people completed this guide.
Author
with 7 other contributors
Shuti Wu
Member since: 10/20/2014
530 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
UMass Dartmouth, Team 5-3, Vijaybhaskar Fall 2014
Member of UMass Dartmouth, Team 5-3, Vijaybhaskar Fall 2014
UMASSD-VIJAYBHASKAR-F14S5G3
4 Members
8 Guides authored
omeyo innocent - Jun 30, 2017
Reply
good
it a good advise and easy
Ghulam Qamar - Aug 3, 2017
Reply
Its really helpful and so easy … thanks
