Imac Intel 21 5 Emc 2638 Fan Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes - 1 hour

Sections

Display Assembly
18 steps
Display
5 steps
Fan
3 steps

Flags

BackiMac Intel 21.5" EMC 2638 & EMC 2742 Late 2013
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Display Assembly

With the hinge free to move, the iMac will be unbalanced and hard to work on. Repairs are fast and easy with an iMac service wedge, but can be completed without one.
If you are using the iFixit cardboard service wedge, follow these assembly directions to put it together.
Before beginning any work on your iMac: Unplug the computer and press and hold the power button for ten seconds to discharge the power supply’s capacitors.
Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply. Only handle the board by the edges.

With the hinge free to move, the iMac will be unbalanced and hard to work on. Repairs are fast and easy with an iMac service wedge, but can be completed without one.

If you are using the iFixit cardboard service wedge, follow these assembly directions to put it together.

Before beginning any work on your iMac: Unplug the computer and press and hold the power button for ten seconds to discharge the power supply’s capacitors.

Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply. Only handle the board by the edges.

1024

Step 2

Starting on the left of the display, near the power button, insert the iMac Opening Tool into the gap between the glass panel and the rear enclosure.
The hub on the iMac Opening Tool will keep you from pushing the wheel in too far. If using a different tool, insert no more than 3/8" into the display. Otherwise, you risk severing antenna cables and causing serious damage.

Starting on the left of the display, near the power button, insert the iMac Opening Tool into the gap between the glass panel and the rear enclosure.

The hub on the iMac Opening Tool will keep you from pushing the wheel in too far. If using a different tool, insert no more than 3/8" into the display. Otherwise, you risk severing antenna cables and causing serious damage.

Step 3

Use the tool like a pizza cutter—roll it along through the gap, and it will cut the foam adhesive through the center.
Be sure to always push with the handle behind the cutting wheel. If you pull, the wheel might get pulled out of the handle.
Run the tool up along the left side of the display.

Use the tool like a pizza cutter—roll it along through the gap, and it will cut the foam adhesive through the center.

Be sure to always push with the handle behind the cutting wheel. If you pull, the wheel might get pulled out of the handle.

Run the tool up along the left side of the display.

Step 4

Continue running the tool up around the top left corner.

Continue running the tool up around the top left corner.

Step 5

Cut the adhesive along the top left of the display.

Cut the adhesive along the top left of the display.

Step 6

Continue along the top of the display.
You may want to run the tool back and forth through what you’ve already cut a few times, to ensure you get as much of the adhesive separated as possible.

Continue along the top of the display.

You may want to run the tool back and forth through what you’ve already cut a few times, to ensure you get as much of the adhesive separated as possible.

Step 7

Push the tool around the top right corner of the display.

Push the tool around the top right corner of the display.

Step 8

Wheel the tool down along the right side of the display.

Wheel the tool down along the right side of the display.

Step 9

Finish pushing the opening tool to the bottom of the right side of the display.
At this point, you’ll want to run the tool back around the entire display, to ensure you cut as much adhesive as possible.

Finish pushing the opening tool to the bottom of the right side of the display.

At this point, you’ll want to run the tool back around the entire display, to ensure you cut as much adhesive as possible.

Step 10

While the opening tool cut most of the adhesive, the display will still be slightly adhered to the case. A plastic card will be necessary to free up the last of this adhesive.
Set the iMac face-up on a table.
Starting from the top right corner of the iMac, wedge a plastic card between the display and frame.
Be careful not to insert the plastic card more than 3/8", or you may damage internal components.

While the opening tool cut most of the adhesive, the display will still be slightly adhered to the case. A plastic card will be necessary to free up the last of this adhesive.

Set the iMac face-up on a table.

Starting from the top right corner of the iMac, wedge a plastic card between the display and frame.

Be careful not to insert the plastic card more than 3/8", or you may damage internal components.

Step 11

Gently twist the plastic card sideways to create a gap between the display and frame.
Move slowly and be careful not to stress the display glass too much—you only need to make a gap of about 1/4".

Gently twist the plastic card sideways to create a gap between the display and frame.

Move slowly and be careful not to stress the display glass too much—you only need to make a gap of about 1/4".

Step 12

Slide the card toward the center of the display to cut any of the remaining adhesive along the top right corner of the iMac.
Be sure to stop before the iSight camera, or you may damage it.

Slide the card toward the center of the display to cut any of the remaining adhesive along the top right corner of the iMac.

Be sure to stop before the iSight camera, or you may damage it.

Step 13

Wedge the plastic card into the top right corner once again, and leave it there to prevent the adhesive from resticking.

Wedge the plastic card into the top right corner once again, and leave it there to prevent the adhesive from resticking.

Step 14

Insert a second plastic card into the gap between the display and frame near the top left corner of the iMac.

Insert a second plastic card into the gap between the display and frame near the top left corner of the iMac.

Step 15

Gently twist the card upward, slightly increasing the space between the display and frame.
As with the other side, twist slowly to allow the adhesive time to separate, and be careful not to over-stress the display glass.

Gently twist the card upward, slightly increasing the space between the display and frame.

As with the other side, twist slowly to allow the adhesive time to separate, and be careful not to over-stress the display glass.

Step 16

Slide the plastic card toward the center, again stopping just before the iSight camera.

Slide the plastic card toward the center, again stopping just before the iSight camera.

Step 17

Wedge the plastic card back into the top left corner.

Wedge the plastic card back into the top left corner.

Step 18

With both plastic cards inserted as shown near the corners, gently twist the cards sideways to increase the gap between display and case.
If there are any sections that seem to stick and won’t separate, stop twisting and use one of the cards to cut the remaining adhesive.
Begin to lift the top of the display up from the frame.
Only lift the display a few inches—the display data and power cables are still connected to the logic board.

With both plastic cards inserted as shown near the corners, gently twist the cards sideways to increase the gap between display and case.

If there are any sections that seem to stick and won’t separate, stop twisting and use one of the cards to cut the remaining adhesive.

Begin to lift the top of the display up from the frame.

Only lift the display a few inches—the display data and power cables are still connected to the logic board.

Step 19

              Display

While holding the display up with one hand, use the other hand to unplug the display power cable.
Lift the display up enough to have easy access to the connector, but not so much that you stretch the cables and stress their connections (about 8").

While holding the display up with one hand, use the other hand to unplug the display power cable.

Lift the display up enough to have easy access to the connector, but not so much that you stretch the cables and stress their connections (about 8").

Step 20

Use the tip of a spudger to flip up the metal retaining bracket on the display data cable.
Carefully pull the display data cable from its socket on the logic board.
Be sure to pull the display data cable connector straight out of its socket.

Use the tip of a spudger to flip up the metal retaining bracket on the display data cable.

Carefully pull the display data cable from its socket on the logic board.

Be sure to pull the display data cable connector straight out of its socket.

Step 21

Lift the display up to a near-vertical position.
At this point there is still a strip of adhesive along the bottom of the display, that will hold the display to the frame like a hinge. You can loosen this adhesive by working the display up and down a few times.

Lift the display up to a near-vertical position.

At this point there is still a strip of adhesive along the bottom of the display, that will hold the display to the frame like a hinge. You can loosen this adhesive by working the display up and down a few times.

Step 22

Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply (boxed in red).
Grasp the small tab at the end of one of the bottom edge display adhesive strips and pull the adhesive toward the top of the iMac to remove it.
Repeat this step with the other adhesive strip and remove it.
If either adhesive strip breaks before it’s removed, use a plastic card to slice through the remaining adhesive.

Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply (boxed in red).

Grasp the small tab at the end of one of the bottom edge display adhesive strips and pull the adhesive toward the top of the iMac to remove it.

Repeat this step with the other adhesive strip and remove it.

If either adhesive strip breaks before it’s removed, use a plastic card to slice through the remaining adhesive.

Step 23

Lift the display up from the frame and remove it from the iMac.
It may be necessary to slowly lift from one side, to peel against the remaining adhesive.
Be very careful handling the display—it’s big, heavy, and made of glass.
During reassembly, head over to our display adhesive guide to install the new adhesive.

Lift the display up from the frame and remove it from the iMac.

It may be necessary to slowly lift from one side, to peel against the remaining adhesive.

Be very careful handling the display—it’s big, heavy, and made of glass.

During reassembly, head over to our display adhesive guide to install the new adhesive.

Step 24

Fan

Pull the fan cable connector straight away from its socket on the logic board.

Pull the fan cable connector straight away from its socket on the logic board.

Step 25

Remove the three 12.3 mm T10 shoulder screws from the fan enclosure.

Remove the three 12.3 mm T10 shoulder screws from the fan enclosure.

Step 26

Lift and remove the fan from the iMac.

Lift and remove the fan from the iMac.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      8 other people completed this guide.

Author

                                      with 4 other contributors

                    Sam Goldheart

Member since: 10/18/2012

455,549 Reputation

                                      548 Guides authored                  



                       Badges:
                       48







                                                        +45 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team