Difficulty
Moderate
Steps
13
Time Required
Suggest a time??
Sections
6
- Battery
- 2 steps
- Casing
- 2 steps
- Antenna Base
- 1 step
- Motherboard
- 4 steps
- Front Panel
- 2 steps
- Switchboard
- 2 steps
Flags
0
BackInsignia NS-B4111
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Unplug and remove the power cord. Turn the boombox upside down.
- Grip the sides of the case and use your thumbs to pop open the battery cover.
Unplug and remove the power cord. Turn the boombox upside down.
Grip the sides of the case and use your thumbs to pop open the battery cover.
1024
Step 2
- Pry out the batteries with your fingers.
Pry out the batteries with your fingers.
Step 3
Casing
- Turn the boombox upside down again. With the Phillips PH1 or the Flathead #3 screwdriver, remove the three 14mm black screws.
- Remove the four 18mm chrome screws with the Phillips PH1 screwdriver.
Turn the boombox upside down again. With the Phillips PH1 or the Flathead #3 screwdriver, remove the three 14mm black screws.
Remove the four 18mm chrome screws with the Phillips PH1 screwdriver.
Step 4
- Gently remove the bottom half of the casing from the top half of the casing.
- The antenna base is connected to the motherboard by a red wire. This wire will prevent the two halves from separating completely.
Gently remove the bottom half of the casing from the top half of the casing.
The antenna base is connected to the motherboard by a red wire. This wire will prevent the two halves from separating completely.
Step 5
Antenna Base
- Remove the 10mm chrome screw from the antenna base with the Phillips PH1 screwdriver. Remove the antenna base from the casing.
- This red wire will now be loose and you can move it out of the antenna base slot.
Remove the 10mm chrome screw from the antenna base with the Phillips PH1 screwdriver. Remove the antenna base from the casing.
This red wire will now be loose and you can move it out of the antenna base slot.
Step 6
Motherboard
- Unscrew the four 12.5mm screws with the Phillips PH1 Screwdriver.
- Unscrew the one 10mm long screw with the Phillips PH1 Screwdriver.
Unscrew the four 12.5mm screws with the Phillips PH1 Screwdriver.
Unscrew the one 10mm long screw with the Phillips PH1 Screwdriver.
Step 7
- Orient the device so that the back is facing you.
- Unplug the six pin male/female header from its socket on the motherboard. The wires on the header are these colors: burgundy, red, orange, yellow, green, and blue.
- Use a tweezer if you find it hard to pull the header out with your fingers.
- Gently pull out the ribbon cable from its socket on the motherboard.
- Pay attention to the orientation of the header and the ribbon cable. Replacing the wires the wrong way may short circuit the board.
Orient the device so that the back is facing you.
Unplug the six pin male/female header from its socket on the motherboard. The wires on the header are these colors: burgundy, red, orange, yellow, green, and blue.
Use a tweezer if you find it hard to pull the header out with your fingers.
Gently pull out the ribbon cable from its socket on the motherboard.
Pay attention to the orientation of the header and the ribbon cable. Replacing the wires the wrong way may short circuit the board.
Step 8
- Rotate the device so that the front is facing you.
- Unplug the four pin header from its socket on the motherboard. The wires on the header are these colors: brown, red, orange, and yellow.
- Use a tweezer if you find it hard to pull this header out with your fingers.
- Gently pull out the ribbon cable from its socket.
- Pay attention to the orientation of the header and the ribbon cable. Replacing the base the wrong way may short circuit the board.
Rotate the device so that the front is facing you.
Unplug the four pin header from its socket on the motherboard. The wires on the header are these colors: brown, red, orange, and yellow.
Use a tweezer if you find it hard to pull this header out with your fingers.
Gently pull out the ribbon cable from its socket.
Pay attention to the orientation of the header and the ribbon cable. Replacing the base the wrong way may short circuit the board.
Step 9
- Pull out the two pin header from its socket on the motherboard. The wires on this header are black and white.
- Use a tweezer if you find it hard to pull this cable out with your fingers.
Pull out the two pin header from its socket on the motherboard. The wires on this header are black and white.
Use a tweezer if you find it hard to pull this cable out with your fingers.
Step 10
Front Panel
- Remove the four 8.5mm chrome screws from the front panel with the Phillips PH1 screwdriver.
Remove the four 8.5mm chrome screws from the front panel with the Phillips PH1 screwdriver.
Step 11
- Remove the front panel from the top casing.
Remove the front panel from the top casing.
Step 12
Switchboard
- Remove the 10.5 mm screws in the corners with the Phillips PH1 screwdriver.
- Remove the two 10.5 mm screws near the center of the board with the Phillips PH1 screwdriver.
Remove the 10.5 mm screws in the corners with the Phillips PH1 screwdriver.
Remove the two 10.5 mm screws near the center of the board with the Phillips PH1 screwdriver.
Step 13
- Lift the board to remove it from the front panel.
Lift the board to remove it from the front panel.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Sabuk Ketvirtis
Member since: 09/21/2016
166 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
UC Davis, Team 1-5, Oliver Fall 2016
Member of UC Davis, Team 1-5, Oliver Fall 2016
UCD-OLIVER-F16S1G5
5 Members
11 Guides authored
