Difficulty
Moderate
Steps
11
Time Required
Suggest a time??
Sections
3
- Rear Panel
- 6 steps
- Hard Drive
- 3 steps
- Hard Drive Cable
- 2 steps
Flags
0
BackiPod 2nd Generation
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Panel
- Before opening your iPod, ensure that the hold switch is in the locked position.
Before opening your iPod, ensure that the hold switch is in the locked position.
1024
Step 2
- Opening the iPod can be challenging. Don’t get discouraged if it takes a few tries before the iPod is opened.
- Insert a plastic iPod opening tool in the seam between the white plastic front and metal back of the iPod. Once you’ve inserted the tool, run it along the seam to free the five tabs holding the iPod together.
Opening the iPod can be challenging. Don’t get discouraged if it takes a few tries before the iPod is opened.
Insert a plastic iPod opening tool in the seam between the white plastic front and metal back of the iPod. Once you’ve inserted the tool, run it along the seam to free the five tabs holding the iPod together.
Step 3
- Continue to run the opening tool along the side of the case until all five tabs have been released.
Continue to run the opening tool along the side of the case until all five tabs have been released.
Step 4
- Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.
Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.
Step 5
- Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.
Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.
Step 6
- Lift the rear panel away from the iPod, making sure it doesn’t catch on the headphone jack.
Lift the rear panel away from the iPod, making sure it doesn’t catch on the headphone jack.
Step 7
Hard Drive
- Peel up the metallic tape attached to the top of the battery.
Peel up the metallic tape attached to the top of the battery.
Step 8
- Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).
Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).
Step 9
- Carefully disconnect the orange ribbon cable from the hard drive.
- If the cable doesn’t come free easily, it may be helpful to gently wiggle the cable from side to side.
- Lift the hard drive out of the iPod.
Carefully disconnect the orange ribbon cable from the hard drive.
If the cable doesn’t come free easily, it may be helpful to gently wiggle the cable from side to side.
Lift the hard drive out of the iPod.
Step 10
Hard Drive Cable
- For the following step, you only need to move the locking bar about 2 mm. Pushing too hard or too far will damage the connector.
- Loosen the connector by pulling the brown locking bar toward the hard drive cable using the tips of your fingers.
For the following step, you only need to move the locking bar about 2 mm. Pushing too hard or too far will damage the connector.
Loosen the connector by pulling the brown locking bar toward the hard drive cable using the tips of your fingers.
Step 11
- Slide the hard drive cable out of its connector.
Slide the hard drive cable out of its connector.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 1 other contributor
iRobot
Member since: 09/24/2009
1 Reputation
646 Guides authored
Badges:
36
+33 more badges