Difficulty

Difficult

Steps

8

Time Required

                          15 - 20 minutes

Sections

1

  • Base
  • 8 steps

Flags

0

  • BackKeurig B70 Platinum

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

This guide will show you how to remove the plastic base surrounding the Keurig B70 Platinum device.

You will need a Phillips #2 screwdriver to complete this guide.

What you need

Step 1

              Base
  • Turn off and unplug the Keurig before starting.
  • Turn the Keurig upside down so the metal base is exposed.
  • Remove the five 12.0 mm screws.

Turn off and unplug the Keurig before starting.

Turn the Keurig upside down so the metal base is exposed.

Remove the five 12.0 mm screws.

1024

Step 2

  • Lift the metal plate off the Keurig and hang it over the side of the device.
  • Be careful! The metal plate is sharp!
  • There are wires connected to the metal plate. Make sure the wires are not in the way of the internal components.

Lift the metal plate off the Keurig and hang it over the side of the device.

Be careful! The metal plate is sharp!

There are wires connected to the metal plate. Make sure the wires are not in the way of the internal components.

Step 3

  • Remove the three 11.0 mm screws located on the upper left side of the base from within the tub-looking area.
  • Pull out the red and white wires and put it off to the side of the Keurig.

Remove the three 11.0 mm screws located on the upper left side of the base from within the tub-looking area.

Pull out the red and white wires and put it off to the side of the Keurig.

Step 4

  • Pull out the water collector by gripping it tightly and lifting upwards.

Pull out the water collector by gripping it tightly and lifting upwards.

Step 5

  • Lift the tube, connected to the tank, off the black plastic hook and leave it off to the side of the hook.

Lift the tube, connected to the tank, off the black plastic hook and leave it off to the side of the hook.

Step 6

  • Pull the power cord out from the plastic holder located near the water tank.
  • This step requires a bit of force so don’t be afraid to pull harder!

Pull the power cord out from the plastic holder located near the water tank.

This step requires a bit of force so don’t be afraid to pull harder!

Step 7

  • Remove the six 13.0 mm screws.

Remove the six 13.0 mm screws.

Step 8

  • Lift the metal base and hover it over the opening of the black plastic base.
  • Carefully raise the plastic base over the metal base until it is removed.
  • Make sure to pull the power cord through the base as well!

Lift the metal base and hover it over the opening of the black plastic base.

Carefully raise the plastic base over the metal base until it is removed.

Make sure to pull the power cord through the base as well!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Steven Tran

Member since: 10/14/2018

329 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UW Tacoma, Team S1-G6, Rose Fall 2018                        

                                                  Member of UW Tacoma, Team S1-G6, Rose Fall 2018 



                    UWT-ROSE-F18S1G6                     


                                            4 Members                     


                                            5 Guides authored