Kodak Easyshare Cd82 Lens Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

7

Time Required

                          1 hour            

Sections

1

• Lens Assembly
• 7 steps

Flags

4

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackKodak EasyShare CD82

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Lens Assembly               

• Remove the batteries and the memory card from the device.
• Remove the two screws located at the bottom of the camera.

Remove the batteries and the memory card from the device.

Remove the two screws located at the bottom of the camera.

1024

Step 2

• Remove the two screws on the side of the device, to left of the camera lens.
• Remove the two screws on side of the device, to the right of the camera lens.
• Pry the casing apart at the seems, starting at the battery compartment.

Remove the two screws on the side of the device, to left of the camera lens.

Remove the two screws on side of the device, to the right of the camera lens.

Pry the casing apart at the seems, starting at the battery compartment.

Step 3

• Remove the front casing from the mid-frame, first.
• Continue to remove the back casing from the mid-frame.
• Do not remove the LCD screen from the device once it becomes visible.

Remove the front casing from the mid-frame, first.

Continue to remove the back casing from the mid-frame.

Do not remove the LCD screen from the device once it becomes visible.

Step 4

• Flip the LCD screen out of the holder from the top to reveal ribbon cable.
• This camera had some obvious water damage..
• Remove the three screws from the LCD holder
• Dislodge the LCD screen holder from the circuit board connector.

Flip the LCD screen out of the holder from the top to reveal ribbon cable.

This camera had some obvious water damage..

Remove the three screws from the LCD holder

Dislodge the LCD screen holder from the circuit board connector.

Step 5

• Disconnect the logic board from the frame on the right side of the device.
• Remove the small ribbon cable, connecting the button board to the logic board, with small pair of tweezers or hemostat.
• Remove the screw on the top right side of the device connecting the LCD screen holder to the midframe.
• Move the black clip into the upward position to disconnect the cable.
• You will now be able to remove the LCD screen and its holder from the device.

Disconnect the logic board from the frame on the right side of the device.

Remove the small ribbon cable, connecting the button board to the logic board, with small pair of tweezers or hemostat.

Remove the screw on the top right side of the device connecting the LCD screen holder to the midframe.

Move the black clip into the upward position to disconnect the cable.

You will now be able to remove the LCD screen and its holder from the device.

Step 6

• Flip the black clips of the connectors into the opposite direction. Remove the lens and CCD cable.
• Remove the two screws securing the lens to the midframe.
• These are missing screws for the CCD sensor, lost in a previous dismantling.
• Remove the single screw securing the lens to the mid-frame. The lens will now be loose.
• Push the lens out of the frame in an angular direction, and remove.

Flip the black clips of the connectors into the opposite direction. Remove the lens and CCD cable.

Remove the two screws securing the lens to the midframe.

These are missing screws for the CCD sensor, lost in a previous dismantling.

Remove the single screw securing the lens to the mid-frame. The lens will now be loose.

Push the lens out of the frame in an angular direction, and remove.

Step 7

• Insert the new lens the same way it was removed.
• Clean and reassemble the camera.

Insert the new lens the same way it was removed.

Clean and reassemble the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 6 other contributors 

                    oldturkey03                     

Member since: 09/29/2010

722,317 Reputation

                                      109 Guides authored                  



                       Badges:
                       53







                                                        +50 more badges                           

Team

                       Global Fixers                        

                                                  Member of Global Fixers 



                    Community                     


                                            22 Members                     


                                            240 Guides authored                     

Sith Siri - Aug 15, 2016

Reply

When it says “Dislodge the LCD screen holder from the circuit board connector” does it mean that I can break that solder without desoldering and it’s okay?