Difficulty
Easy
Steps
8
Time Required
5 - 10 minutes
Sections
2
- Top Assembly
- 4 steps
- Display
- 4 steps
Flags
0
BackLenovo IdeaPad Yoga 11S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Top Assembly
- Remember to power off the device before removing any parts.
- Position the laptop so that the bottom enclosure is facing upward.
- Use a Phillips #0 Screwdriver to remove the ten 1.9mm screws holding the bottom enclosure in place.
- Use an opening tool to carefully pry up the rubber pads.
- Use a Phillips screwdriver to remove the two screws under the rubber pads, which secure the keyboard.
Remember to power off the device before removing any parts.
Position the laptop so that the bottom enclosure is facing upward.
Use a Phillips #0 Screwdriver to remove the ten 1.9mm screws holding the bottom enclosure in place.
Use an opening tool to carefully pry up the rubber pads.
Use a Phillips screwdriver to remove the two screws under the rubber pads, which secure the keyboard.
1024
Step 2
Remove Keyboard
- Flip the laptop over and swing open the display.
- Lift the edge of the keyboard closest to the trackpad up.
- Carefully disconnect keyboard ribbon cable from the laptop.
- Remove the keyboard.
Flip the laptop over and swing open the display.
Lift the edge of the keyboard closest to the trackpad up.
Carefully disconnect keyboard ribbon cable from the laptop.
Remove the keyboard.
Step 3
- Remove the two screws securing the midframe.
Remove the two screws securing the midframe.
Step 4
- Grab the front edge of the top assembly and lift it up carefully.
- There are three ribbon cables that attach the top assembly to the motherboard. Lift carefully to avoid damaging them.
- Gently slide the three ribbon cables out of their slots.
- Remove the top assembly completely by pulling it off of the device.
Grab the front edge of the top assembly and lift it up carefully.
There are three ribbon cables that attach the top assembly to the motherboard. Lift carefully to avoid damaging them.
Gently slide the three ribbon cables out of their slots.
Remove the top assembly completely by pulling it off of the device.
Step 5
Display
- Keep the device positioned where it sits on the bottom encasing with the display open.
- Locate the four 1.9mm screws used to attach the display brackets to the bottom enclosure of the device.
- Use a Phillips #00 Screwdriver to remove the four screws.
Keep the device positioned where it sits on the bottom encasing with the display open.
Locate the four 1.9mm screws used to attach the display brackets to the bottom enclosure of the device.
Use a Phillips #00 Screwdriver to remove the four screws.
Step 6
- Use a plastic opening tool to lift the retaining flap to disconnect the right display cable connector.
- Gently pull the display cable out of the socket.
Use a plastic opening tool to lift the retaining flap to disconnect the right display cable connector.
Gently pull the display cable out of the socket.
Step 7
- Use a plastic opening tool to lift the retaining flap to disconnect the left display cable connector.
- Gently pull the display cable out of the socket.
Use a plastic opening tool to lift the retaining flap to disconnect the left display cable connector.
Step 8
- Gently lift the display to detach it from the device.
Gently lift the display to detach it from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 2 other contributors
Landon Epps
Member since: 03/26/2015
982 Reputation
5 Guides authored
Badges:
19
+16 more badges
Team
Baylor, Team 7-11, Williams Spring 2015
Member of Baylor, Team 7-11, Williams Spring 2015
BU-WILLIAMS-S15S7G11
3 Members
10 Guides authored
