Lenovo Slim Dvd Burner Db65 Usb 2 0 Power Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          15 minutes            

Sections

1

• USB 2.0 Power Assembly
• 11 steps

Flags

0

• BackLenovo Slim DVD Burner DB65

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              USB 2.0 Power Assembly               

• Flip the unit over so the bottom is facing you.
• Remove the two black 7.6mm Phillips #0 screws from the bottom cover.

Flip the unit over so the bottom is facing you.

Remove the two black 7.6mm Phillips #0 screws from the bottom cover.

1024

Step 2

• Use the iFixit Opening Tool to gently pry the unit apart to gain access to the interior.
• If the top seems stuck, run the iFixit Opening Tool along the edge while simultaneously pulling up on the top with your fingers. Continue to apply pressure until it opens completely.

Use the iFixit Opening Tool to gently pry the unit apart to gain access to the interior.

If the top seems stuck, run the iFixit Opening Tool along the edge while simultaneously pulling up on the top with your fingers. Continue to apply pressure until it opens completely.

Step 3

• Open the device tray by inserting a paper clip into the eject hole.

Open the device tray by inserting a paper clip into the eject hole.

Step 4

• Remove the two silver 3mm Phillips #0 screws from the mini USB circuit board.

Remove the two silver 3mm Phillips #0 screws from the mini USB circuit board.

Step 5

• Turn the unit over and remove the two silver 3mm Phillips #0 screws from the aluminum cover.

Turn the unit over and remove the two silver 3mm Phillips #0 screws from the aluminum cover.

Step 6

• Lift up and remove the silver cover to expose the internal components.
• If the cover seems stuck gently pull up on one edge. The cover should remove completely after one side is free.

Lift up and remove the silver cover to expose the internal components.

If the cover seems stuck gently pull up on one edge. The cover should remove completely after one side is free.

Step 7

• Remove the two ribbon cables using any pair of ESD(electrostatic discharge) safe tweezers.
• The ribbons wires are fragile but still require a firm force to remove.

Remove the two ribbon cables using any pair of ESD(electrostatic discharge) safe tweezers.

The ribbons wires are fragile but still require a firm force to remove.

Step 8

• Use the iFixit Opening Tool to flip up the grey locking flap on the ZIF (zero insertion force) connector to allow removal of the ribbon cable.
• Remove the large ribbon wire using any pair of ESD safe tweezers.

Use the iFixit Opening Tool to flip up the grey locking flap on the ZIF (zero insertion force) connector to allow removal of the ribbon cable.

Remove the large ribbon wire using any pair of ESD safe tweezers.

Step 9

• Remove the single 3mm Phillips #0 screw to loosen the large circuit board.

Remove the single 3mm Phillips #0 screw to loosen the large circuit board.

Step 10

• Pull up on the large circuit board and slide it through the opening with the ribbon cable attached to it.
• The large circuit board should end up on the other side of the device next to the Mini USB circuit board.

Pull up on the large circuit board and slide it through the opening with the ribbon cable attached to it.

The large circuit board should end up on the other side of the device next to the Mini USB circuit board.

Step 11

• Remove the power assembly by peeling it away from the unit.
• The two circuit boards, which make up the power assembly, are connected together with a white ribbon cable.
• Take your time when removing the power assembly, as it requires a firm amount of force to peel away and remove.

Remove the power assembly by peeling it away from the unit.

The two circuit boards, which make up the power assembly, are connected together with a white ribbon cable.

Take your time when removing the power assembly, as it requires a firm amount of force to peel away and remove.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 

                    Matthew Green                     

Member since: 07/05/2018

337 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge                           

Team

                       IUPUI, Team S2-G1, Harley Summer 2018                        

                                                  Member of IUPUI, Team S2-G1, Harley Summer 2018 



                    IUPUI-HARLEY-SU18S2G1                     


                                            3 Members                     


                                            2 Guides authored