Difficulty
Moderate
Steps
10
Time Required
25 minutes
Sections
5
- Battery
- 3 steps
- Back Plate
- 1 step
- Keyboard
- 2 steps
- Front Compartment Case
- 2 steps
- CD Disk Drive
- 2 steps
Flags
3
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackLenovo ThinkPad Edge E520
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Power off and unplug the computer before the start of these steps.
- Close the laptop lid.
Power off and unplug the computer before the start of these steps.
Close the laptop lid.
1024
Step 2
- Flip the computer so that the back is facing upwards.
- Locate the switch used to release the battery.
- The switch should be located towards the hinge of the laptop near the battery pack and have a lock icon associated with it.
Flip the computer so that the back is facing upwards.
Locate the switch used to release the battery.
The switch should be located towards the hinge of the laptop near the battery pack and have a lock icon associated with it.
Step 3
- Slide the switch towards the unlocked lock icon.
- While holding it in the unlocked position, slide the battery towards the hinge.
- Fully separate the battery pack from the back of the laptop.
Slide the switch towards the unlocked lock icon.
While holding it in the unlocked position, slide the battery towards the hinge.
Fully separate the battery pack from the back of the laptop.
Step 4
Back Plate
- Flip over the laptop and position it with the battery being furthest away from you.
- Remove the four screws on the edges of the T-Shaped plate with a Phillips #0 screwdriver.
- Remove the T-Shaped plate from the back of the computer. It should come off easily if all four aforementioned screws are removed.
- Screw length 6.35 mm, head 3.175 mm
Flip over the laptop and position it with the battery being furthest away from you.
Remove the four screws on the edges of the T-Shaped plate with a Phillips #0 screwdriver.
Remove the T-Shaped plate from the back of the computer. It should come off easily if all four aforementioned screws are removed.
Screw length 6.35 mm, head 3.175 mm
Step 5
Keyboard
- There are two screws that have keyboard symbols pointing at them.
- Unscrew the screws with a 3.175 mm diameter and 6.35 mm length with a Phillips head screwdriver.
There are two screws that have keyboard symbols pointing at them.
Unscrew the screws with a 3.175 mm diameter and 6.35 mm length with a Phillips head screwdriver.
Step 6
- Turn the laptop back over so that the keyboard is facing you.
- Use your hands to separate the keyboard from the laptop
Turn the laptop back over so that the keyboard is facing you.
Use your hands to separate the keyboard from the laptop
Step 7
Front Compartment Case
- Remove all remaining screws on the back of the device.
- Screw length 6.35 mm, head 3.175 mm Screws behind battery length 3.175 mm, head 3.175 mm
Remove all remaining screws on the back of the device.
Screw length 6.35 mm, head 3.175 mm Screws behind battery length 3.175 mm, head 3.175 mm
Step 8
- Flip device back over and open the screen.
- Insert the prying tool on one edge of the case and follow along all four edges until the case frees up.
- Remove the case.
Flip device back over and open the screen.
Insert the prying tool on one edge of the case and follow along all four edges until the case frees up.
Remove the case.
Step 9
CD Disk Drive
- The silver block contains two screws.
- Unscrew the two screws to remove the clamp that holds the disk drive in place.
- Screw length 6.35 mm, head 3.175 mm
The silver block contains two screws.
Unscrew the two screws to remove the clamp that holds the disk drive in place.
Step 10
- Remove the screws holding the disk drive in place and then slide outwards to remove
- Screw length 6.35 mm, head 3.175 mm
Remove the screws holding the disk drive in place and then slide outwards to remove
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Andrew Martin
Member since: 03/01/2018
187 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
UMass Dartmouth, Team S1-G2, Simcock Spring 2018
Member of UMass Dartmouth, Team S1-G2, Simcock Spring 2018
UMASSD-SIMCOCK-S18S1G2
4 Members
12 Guides authored
